Extended Inner Ring Self-Aligning Ball Bearings combine two-row angular self-alignment with an extended inner ring designed for simplified shaft locating and anti-rotation.
The continuous spherical outer-ring raceway allows the bearing to compensate for angular misalignment between the shaft and housing. The extended inner ring provides extra mounting surface length along the shaft and includes a locating slot for engagement with a locating pin or shoulder screw. This configuration is engineered for machinery using commercial-grade shafting where rapid assembly, simple shaft location, and tolerance compensation are required.
Key Product Features
Dual-Row Self-Alignment: Accommodates shaft deflections and angular misalignment without increasing friction or edge stresses.
Extended Inner Ring & Locating Slot: Extends shaft contact area and accepts a locating pin or shoulder screw to lock the inner ring axially and prevent rotation.
Cylindrical Bore: Standardized ISO cylindrical bore allows direct mounting onto ground commercial shafting.
Sealed or Open Variants: Available open for relubrication systems, or sealed with contact seals pre-filled with high-performance grease.
Technical Specifications & Standard Product Range
All boundary dimensions and tolerances conform to ISO 15 (Radial Bearings Boundary Dimensions) and ISO 492 (Tolerance Classes).
|
Bearing Designation |
Bore Diameter d (mm) |
Outside Diameter D (mm) |
Outer Ring Width B (mm) |
Inner Ring Width C (mm) |
Dynamic Load Rating Cr (kN) |
Static Load Rating C0r (kN) |
Limiting Speed Grease (RPM) |
Weight (kg) |
|
11204 |
20 |
47 |
14 |
24 |
12.7 |
3.40 |
14,000 |
0.13 |
|
11205 |
25 |
52 |
15 |
25 |
14.3 |
4.00 |
12,000 |
0.16 |
|
11206 |
30 |
62 |
16 |
27 |
15.6 |
4.65 |
10,000 |
0.24 |
|
11207 |
35 |
72 |
17 |
29 |
15.9 |
5.10 |
9,000 |
0.35 |
|
11208 |
40 |
80 |
18 |
31 |
19.0 |
6.55 |
8,000 |
0.44 |
|
11209 |
45 |
85 |
19 |
33 |
21.6 |
7.35 |
7,500 |
0.49 |
|
11210 |
50 |
90 |
20 |
35 |
23.0 |
8.15 |
6,700 |
0.54 |
Application Suitability & Design Selection
|
Operating Requirement |
Extended Inner Ring Design |
Standard Self-Aligning Ball Bearing |
Alternative Bearing Choice |
|
Angular Misalignment |
High (Up to 2.5 degrees) |
High (Up to 2.5 degrees) |
Spherical Roller Bearing (For heavy loads) |
|
Shaft Anti-Rotation |
Mechanical Slot / Pin Lock |
Interference Fit / Sleeve Required |
Setscrew / Eccentric Locking Collar |
|
Axial Load Capacity |
Low to Moderate |
Low to Moderate |
Angular Contact / Deep Groove Bearing |
|
Radial Load Capacity |
Moderate |
Moderate |
Spherical / Cylindrical Roller Bearing |
|
Mounting Complexity |
Simplified |
Requires Press / Sleeve |
Application Dependent |
|
Primary Applications |
Agricultural, Textiles, Conveyors, Paper Processing, Material Handling |
General Industrial Machinery |
High-Precision Machine Tool Spindles |
Manufacturing Standards & Quality Assurance
Quality Control Specifications
|
Parameter Inspected |
Measuring Equipment / Method |
Standard Applied |
|
Bore & OD Tolerances |
Multi-Jet Air Gauges / OD Micrometers |
ISO 492 |
|
Raceway Profile & Runout |
Roundness & Form Measuring System |
DIN ISO 1101 |
|
Material Hardness |
Rockwell Hardness Tester (60-65 HRC) |
ISO 6508 |
|
Internal Clearance |
Radial Internal Clearance (RIC) Gauge |
ISO 5753-1 |
|
Vibration & Noise |
Anderometer / Vibration Spectrum Analyzer |
ISO 15242 |
Step-by-Step Selection Workflow
|
Step |
Engineering Action |
Parameters Checked |
|
1. Shaft Verification |
Measure actual shaft diameter and surface finish. |
Recommended surface finish Ra <= 1.6 um. |
|
2. Load Calculation |
Calculate combined dynamic load P = Fr + Y * Fa. |
Verify P is within rated dynamic capacity (Cr). |
|
3. Speed Rating |
Cross-reference operating RPM with limiting speed. |
Adjust for grease fill or contact seal drag. |
|
4. Internal Clearance |
Select clearance class based on temperature fit. |
Choose Normal (CN), C3, or C4. |
|
5. Hardware Check |
Verify slot width against pin/screw dimensions. |
Ensure proper clearance to prevent binding. |
FAQ
Q: How does the extended inner ring prevent shaft slipping?
A: The extended inner ring features an integrated slot that engages a locating pin or shoulder screw installed on the shaft. This positive mechanical lock prevents the inner ring from rotating independently (creeping) under operational torque.
Q: What level of angular misalignment can these bearings accommodate?
A: Depending on the bearing series, seal configuration, and radial internal clearance, these bearings can accommodate angular misalignments between 1.5 degrees and 2.5 degrees without degrading operational life.
Q: When should I choose an extended inner ring bearing over a standard self-aligning bearing?
A: Choose the extended inner ring design when using standard commercial shafting where press-fit tolerances are impractical, or when quick installation, removal, and positive shaft positioning via locating pins are required.
Q: Are these bearings suitable for heavy axial loads?
A: No. Self-aligning ball bearings are primarily designed for radial loads and moderate misalignment. For applications involving high axial forces, angular contact ball bearings or spherical roller bearings should be specified.
Q: What quality documentation is provided with OEM orders?
A: Every bulk order is supplied with an EN 10204 3.1 Inspection Certificate, including dimensional measurement sheets, heat treatment logs, raw material trace certificates, and a Certificate of Conformity (CoC).
Hot Tags: extended inner ring self-aligning ball bearings, China extended inner ring self-aligning ball bearings manufacturers, suppliers, factory, Round Hole Disc Bearings

